Hello, I got this error msg while burning a DVD-R with nero. The DVD-R is a TDK 16X. Perhaps the disk is the problem since my recorder (<_NEC DVD_RW ND-2510A) can only burn up to 4X (I think). Nevertheless, even If I tell to Nero to buen at 1X speed, I got the same error : Code: Nicolas a 1A... Windows XP 5.1 IA32 WinAspi: File 'Wnaspi32.dll': Ver=?.?.?.?, size=6656 bytes, created 7/10/2003 18:08:44 ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 18:35:34 Nero Version: 6.6.0.15 Internal Version: 6, 6, 0, 15h Recorder: <_NEC DVD_RW ND-2510A> Version: 2.54 - HA 0 TA 1 - 6.6.0.15 Adapter driver: <atapi> HA 0 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ATAPI CD-ROM: <HL-DT-ST DVD-ROM GDR8163B>Version: 0N21 - HA 0 TA 0 - 6.6.0.15 Adapter driver: <atapi> HA 0 === Scsi-Device-Map === CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 0 ID 0 DMA: On CdRomPeripheral : _NEC DVD_RW ND-2510A atapi Port 0 ID 1 DMA: On DiskPeripheral : ST3200822AS atapi Port 1 ID 0 DMA: On CdRomPeripheral : XI5046D LEM850I 1.0 dtscsi Port 4 ID 0 DMA: Off === CDRom-Device-Map === HL-DT-ST DVD-ROM GDR8163B D: CDRom0 _NEC DVD_RW ND-2510A E: CDRom1 XI5046D LEM850I L: CDRom2 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte ShowDrvBufStat : 0 BUFE : 0 Physical memory : 1023MB (1048044kB) Free physical memory: 484MB (496328kB) Memory in use : 52 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 23.8.2007 ISO compilation 19:27:23 #1 Text 0 File Isodoc.cpp, Line 6314 Iso document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : TRUE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : TRUE 19:27:23 #2 Text 0 File Reader.cpp, Line 127 Reader running 19:27:23 #3 ISO9660GEN -11 File geniso.cpp, Line 3309 First writeable address = 0 (0x00000000) 19:27:23 #4 Text 0 File Burncd.cpp, Line 3231 Turn on Disc-At-Once, using DVD media 19:27:29 #5 Text 0 File DlgWaitCD.cpp, Line 269 Last possible write address on media: 2298495 (510:46.45, 4489MB) Last address to be written: 2148607 (477:28.07, 4196MB) 19:27:29 #6 Text 0 File DlgWaitCD.cpp, Line 281 Write in overburning mode: NO (enabled: CD) 19:27:29 #7 Text 0 File DlgWaitCD.cpp, Line 2477 Recorder: _NEC DVD_RW ND-2510A, Media type: DVD-R Disc Manufacturer: TTH02 - Disc Application Code: 64, Disc Physical Code: 193 19:27:29 #8 Text 0 File DlgWaitCD.cpp, Line 447 >>> Protocol of DlgWaitCD activities: <<< ========================================= 19:27:29 #9 Text 0 File ThreadedTransferInterface.cpp, Line 830 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 2148608 (2148608) = #2148608/477:28.8 relocatable, disc pos for caching/writing not required/ required, no patch infos -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2148608 blocks [_NEC DVD_RW ND-2510A] -------------------------------------------------------------- 19:27:29 #10 Text 0 File ThreadedTransferInterface.cpp, Line 1043 Prepare recorder [_NEC DVD_RW ND-2510A] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4400349184, ISRC "" DAO layout: =========== __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0x00 0 | 1 | 0 | 0x41 | 0x00 0 | 1 | 1 | 0x41 | 0x00 2148608 | lead-out | 1 | 0x41 | 0x00 19:27:29 #11 Phase 24 File dlgbrnst.cpp, Line 1832 Caching of files started 19:27:29 #12 Text 0 File Burncd.cpp, Line 4116 Cache writing successful. 19:27:29 #13 Phase 25 File dlgbrnst.cpp, Line 1832 Caching of files completed 19:27:29 #14 Phase 36 File dlgbrnst.cpp, Line 1832 Burn process started at 2.4x (3.324 KB/s) 19:27:29 #15 Text 0 File ThreadedTransferInterface.cpp, Line 2643 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 19:27:29 #16 Text 0 File DVDR.cpp, Line 2357 Recording mode: Sequential Recording Mode 19:27:29 #17 Text 0 File Mmc.cpp, Line 21663 Set BUFE: Buffer underrun protection -> ON 19:27:29 #18 Text 0 File DVDR.cpp, Line 2511 Start write address at LBA 0 DVD high compatibility mode: Yes 19:27:29 #19 Text 0 File Cdrdrv.cpp, Line 8821 ---- DVD Structure: Physical Format Information (00h) ---- Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-R (2), Part Version: 5 Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 26127F h End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Start sector number of the current Border-Out: 2FE10 h Start sector number of the next Border-In: 2FFA0 h Media Specific [16..63]: 00 60 00 10 20 30 40 50 - 00 00 00 21 00 00 00 00 .`...0@P...!.... 00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 19:27:29 #20 SCSI -1046 File Cdrdrv.cpp, Line 1182 SCSI Exec, HA 0, TA 1, LUN 0 Status: 0x04 (0x01, SCSI_ERR) HA-Status 0x00 (0x00, OK) TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x30 Sense Qual: 0x05 CDB Data: 0x53 0x00 0x00 0x00 0x00 0x00 0x20 0xC9 0x00 0x00 0x00 0x00 Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A 0x00 0x00 0x00 0x00 0x30 0x05 19:27:29 #21 CDR -1046 File ThreadedTransferInterface.cpp, Line 1763 Illegal disc 19:27:29 #22 TRANSFER -27 File ThreadedTransferInterface.cpp, Line 1763 Could not perform start of Disc-at-once 19:27:29 #23 Phase 38 File dlgbrnst.cpp, Line 1832 Burn process failed at 2.4x (3.324 KB/s) Existing drivers: File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 17/08/2001 22:07:32 File 'Drivers\PXHELP20.SYS': Ver=2.03.01a, size=20368 bytes, created 6/05/2004 2:03:00 (Prassi/Veritas driver for win 2K) File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 3/08/2004 22:59:44 (Adapter driver for rec) Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option) Any help is welcome ;-) Thanks
Hi nicolasr 1st thing edit out the serial # in the log - it begins w/ 1A. Don't need someone else using it. Did the NEC come with the pc or did you buy it separately? if it came with the pc who is the manufacturer? Trying to check and see of the firmware is up to date. That's usually what the illegal disc error in the log means - the firmware doesn't support the media you are using. WinAspi: File 'Wnaspi32.dll': Ver=?.?.?.?, Check your aspi in Toolkit. In smartstart go to toolkit>info tool>aspi tab. See if anything shows corrupted. If it does post that back. If it says aspi not installed - that's ok. Try using other media - like Verbatim, Taiyo Yuden or made in Japan Sony, Fuji or Maxell.
Thanks for the reply The NEC came with the PC (Packard Bell iMedia 5042) How can I check the firmware (sorry, I have never updated any firmware) ? EDIT: found a firmware update: http://www.de.nec.de/software/2484_FW_ND-2510A_win219-20A.zip The update concerns the DVD 16X ==> seems the good one, but says it is NOT for oem !! => not for me. What can I do ? any idea ? Thanks again
Not a problem For the firmware update you'll need to check Packard Bells site to see if there is one. There may not be - pc manufacturers aren't the best at keeping the drives firmware updated for newer media. Switch the media to the ones listed above. Try 8x media too if you can find it - will hopefully be more supported with this drives firmware.
Hello, if I good understand, if Packard Bell doesn't supply an update, I cannot update the firmware ! (I have not found an update at Pack. Bell :-( ) The only solution is to buy not-16X media ?
That's about right - you can try the one from NEC's page. usually if it's not the right one you'll get a message saying 'target device not found' - no harm. Or you can try the modified 2.19 firmware here - link. I recommend 8x media when a drive hasn't had an update in awhile cause usually the 8x media is more supported.
I have found a solution that works. For those who are interested, follow the instructions here: http://forum.hardware.fr/hfr/Hardware/CD-DVD/topic-officiel-graveur-sujet_627952_51.htm#t5427841 (summary here: http://vvn07.keo.in/blog/index.php?2007/03/24/1013-mise-a-jour-firmware-graveur-dvd-nec-nd-2510a ) [in French] i.e in English: Follow these steps: 1) Download binflah (WIN32 GUI) from http://binflash.cdfreaks.com/ 2) Download the latest official NEC driver (for instance here: http://www.touslesdrivers.com/index.php?v_page=23&v_code=14763 ) 3) In Windows Failsafe mode, launch binflash, select 'Flash' and choose the file "ND-2510A (GEN) K251GN90.exe" from the NEC-drivers 4) That's it ! It works ! Thanks for your help: you helped me to search and finally find the previous solution.
