I have had failures off & on trying to burn DVDs with Nero 7 on my system. I had the drive replaced by Dell before the warranty went out on my PC. Worked for a while but started having problems again. Was getting about 50% good, but now have burned a dozen or more coasters. I have read through this forum & tried a lot of the suggestions, but I haven't had any luck. Burner: NEC ND-3530A in slot "0" (had original in slot "1" but when I replaced it, it wouldn't work in "1" so I moved it up to "0") Have had failures: 1) Burning data DVDs 2) Burning Nero Vision DVD movies 3) Burning DVD files created by Adobe Premiere Elements Note: was able to burn 2 DVD with APE, but now it fails, too. Have tried: 1) Resetting DMA mode on Burner drive. Was able to change, but no effect 2) Updated firmware on burner (to 3.01). No effect 3) Disabled IMAPI. No effect 4) Changed Media (have used Fujifilm & Sony). No effect 5) Tried burning slower (6x & 4x). No effect I did run the NeroInfo tools & it was able to burn a DVD for the test. Not sure if that means anything. Here is the latest failure's log file: 1C82-004K-19E5-MAAX-4001-1MA4-**** 1A4K-0800-0000-2529-4295-**** Windows XP 5.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.10.1.2 Internal Version: 7, 10, 1, 2 Recorder: <_NEC DVD_RW ND-3530A> Version: 3.01 - HA 1 TA 0 - 7.10.1.2 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ? CD-ROM: <_NEC DVD_RW ND-3530A >Version: 3.01 - HA 1 TA 0 - 7.10.1.2 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 0 DMA: On DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 1 DMA: Off CdRomPeripheral : _NEC DVD_RW ND-3530A atapi Port 1 ID 0 DMA: On CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 1 DMA: Off === CDRom-Device-Map === _NEC DVD_RW ND-3530A E: CdRom0 HL-DT-ST DVD-ROM GDR8163B F: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 1022MB (1046620kB) Free physical memory: 575MB (589200kB) Memory in use : 43 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 6.5.2008 UDF/ISO compilation 9:47:40 PM #1 Text 0 File SCSIPTICommands.cpp, Line 424 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 9:47:40 PM #2 Phase 112 File dlgbrnst.cpp, Line 1762 DVD-Video files reallocation started 9:47:40 PM #3 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VIDEO_TS.IFO has been modified 9:47:40 PM #4 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VIDEO_TS.BUP has been modified 9:47:40 PM #5 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VTS_01_0.IFO has been modified 9:47:40 PM #6 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VTS_01_0.BUP has been modified 9:47:40 PM #7 Phase 113 File dlgbrnst.cpp, Line 1762 DVD-Video files reallocation completed 9:47:40 PM #8 Text 0 File Isodoc.cpp, Line 6666 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 UDF Mode : UDF/ISO bridge UDF Options : automatic UDF Revision : 1.02 UDF Partition Type : physical ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : FALSE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : TRUE 9:47:40 PM #9 Phase 111 File dlgbrnst.cpp, Line 1762 DVD-Video files sorted 9:47:40 PM #10 ISO9660GEN -11 File Geniso.cpp, Line 3343 First writeable address = 0 (0x00000000) 9:47:40 PM #11 ISO9660GEN -11 File Geniso.cpp, Line 3343 First writeable address = 0 (0x00000000) 9:47:40 PM #12 Text 0 File Burncd.cpp, Line 3508 Turn on Disc-At-Once, using DVD media 9:47:41 PM #13 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 2295103 (510:01.28, 4482MB) Last address to be written: 1497919 (332:52.19, 2925MB) 9:47:41 PM #14 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 9:47:41 PM #15 Text 0 File DlgWaitCD.cpp, Line 2972 Recorder: _NEC DVD_RW ND-3530A, Media type: DVD+R 9:47:41 PM #16 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 9:47:41 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 793 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 1497920 (1497920) = #1497920/332:52.20 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1497920 blocks [E: _NEC DVD_RW ND-3530A] -------------------------------------------------------------- 9:47:41 PM #18 Text 0 File ThreadedTransferInterface.cpp, Line 995 Prepare [E: _NEC DVD_RW ND-3530A] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3067740160, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 1497920 | 0 | 0x00 1497920 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 9:47:41 PM #19 Text 0 File SCSIPTICommands.cpp, Line 215 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 9:47:41 PM #20 Text 0 File Burncd.cpp, Line 4294 Caching options: cache CDRom or Network-Yes, small files-No (<64KB) 9:47:41 PM #21 Phase 24 File dlgbrnst.cpp, Line 1762 Caching of files started 9:47:41 PM #22 Text 0 File Burncd.cpp, Line 4413 Cache writing successful. 9:47:41 PM #23 Phase 25 File dlgbrnst.cpp, Line 1762 Caching of files completed 9:47:41 PM #24 Phase 36 File dlgbrnst.cpp, Line 1762 Burn process started at 8x (11,080 KB/s) 9:47:41 PM #25 Text 0 File ThreadedTransferInterface.cpp, Line 2721 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 9:47:41 PM #26 SPTI -1066 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1066) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x24 Sense Qual: 0x00 CDB Data: 0xAD 00 00 00 00 00 00 00 08 04 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24 00 00 C0 00 07 Buffer x0617e240: Len x804 9:47:41 PM #27 Text 0 File DVDR.cpp, Line 6787 Drive: _NEC DVD_RW ND-3530A Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 9:47:41 PM #28 CDR -1207 File DVDR.cpp, Line 6481 Book Type automatically set to: DVD-ROM 9:47:41 PM #29 Text 0 File DVDPlusRW.cpp, Line 675 Start write address at LBA 0 DVD high compatibility mode: Yes 9:47:41 PM #30 Text 0 File ThreadedTransfer.cpp, Line 269 Pipe memory size 83836800 9:50:18 PM #31 SPTI -1093 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1093) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x02 Sense Qual: 0x00 CDB Data: 0x2A 00 00 04 13 E0 00 00 20 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 02 Buffer x0bc1ab00: Len x10000 0x00 00 01 BA 44 2E 0F 35 FE 03 01 89 C3 F8 00 00 0x01 E0 07 EC 81 00 00 A5 04 9E CD A5 A3 45 49 29 0x4D AE 04 54 6C 7A 95 61 EC E1 28 8D 2C DA 12 41 9:50:18 PM #32 CDR -1093 File Writer.cpp, Line 303 No seek complete E: _NEC DVD_RW ND-3530A 9:50:18 PM #33 SPTI -1135 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x5B 01 01 00 00 01 00 00 00 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 0C 9:50:18 PM #34 SPTI -1176 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1176) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x72 Sense Qual: 0x03 CDB Data: 0x5B 01 06 00 00 00 00 00 00 00 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 72 03 9:50:18 PM #35 Text 0 File DVDPlusRW.cpp, Line 935 EndDAO: Last written address 267232 9:50:18 PM #36 Text 0 File DVDR.cpp, Line 6787 Drive: _NEC DVD_RW ND-3530A Book Type request [NEC]: DVD-ROM, write to RAM select Book Type setting from RAM Changing the Book Type was finished successfully, return code 0 9:50:18 PM #37 CDR -1176 File WriterStatus.cpp, Line 162 Session fixation error E: _NEC DVD_RW ND-3530A 9:50:18 PM #38 TRANSFER -24 File WriterStatus.cpp, Line 162 Could not perform end of Disc-at-once 9:50:19 PM #39 Phase 38 File dlgbrnst.cpp, Line 1762 Burn process failed at 8x (11,080 KB/s) 9:50:19 PM #40 Text 0 File SCSIPTICommands.cpp, Line 261 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 9:50:22 PM #41 Text 0 File Cdrdrv.cpp, Line 11185 DriveLocker: UnLockVolume completed 9:50:22 PM #42 Text 0 File SCSIPTICommands.cpp, Line 424 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option) Any help would be greatly appreciated.
dma is still off on 2 drives do you have sata hard drives? 2 of them. === Scsi-Device-Map === DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 0 DMA: On DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 1 DMA: Off CdRomPeripheral : _NEC DVD_RW ND-3530A atapi Port 1 ID 0 DMA: On CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 1 DMA: Off i would say check your bios for AUTO DETECTing drives on bootup. also try installing ForceASPI layer...
I have tried a couple of times to get the DMA up on the other two drives, but haven't had much luck. I removed the Primary IDE Channgel via the conrol panel & rebooted. Right now, both Device 0 is set to "DMA if Available" and has a current mode of "Ultra DMA Mode 2." Device 1 is also set to "DMA if Available, but the current mode is PIO. Its the same as when I've tried removing it & rebooting - I've never seen the Device 1 on DMA mode. Thoughts? Yes, I have two HD - both SATA. I used the files for installing the V.71.2 winaspi first. It added two of the files but not the wowpost.exe & winaspi.dll. I then tried the forceaspi. No difference.
OK. Tried the force aspi again, and it worked. Yeah. Tried burning a DVD AND IT WORKED!!!! A bit slow, but at least it finished. Thanks for the hint about winaspi; I thought it wasn't need since I was on XP. The files I was burning were on the primary HD, which seems to be set with DMA right now. However, the 2nd drive is where I store most of my video & photos, which is what I'm backing up or burning DVDs from most of the time. Any hints about getting it "up to speed?"
I should also add, when I look at the IDE ATA/ATAPI Controllers, there are three items: - Intel(R) 82801FB/FBM Ultra ATA Storage Controllers - 266F - Primary IDE Channel - Intel(R) 82801FR SATA AHCI Controller I'm pretty hardware stupid, but when I look at other posts, its implies there should be a secondary IDE channel I can follow the "remove & reboot" process on. It looks the same in the Nero Info tool, and I cannot "expand" the Primary Channel like described in other posts.
not too sure on this as 1 sata hd is on dma and other not? hmmm.... ok did you uninstall this - Intel(R) 82801FB/FBM Ultra ATA Storage Controllers - 266F then reboot? also in this case uninstall the drive itelf too in drives link not ide link. these dvdrw drives did you install them? if so did you set the jumpers correctly?
I tried uninstalling the Ultra ATA & the 2nd HD itself via the drive section. On reboot, both HDs were set to DMA if Available, but currently at "Not application." On reboot, they were back to the same status as before - Device 0 has current mode of DMA & Device 1 has PIO. I did install burner. It was a replacement when the DVD+/-RW drive that came with the computer kept failing. The old drive was in the 1 slot, but the ND-3530a wouldn't work there, so on the advice of Dell, I swapped their locations. (The second drive is just a DVD reader). I checked both of the DVD drives, and both have their jumpers set to the leftmost pair - CSEL setting if I'm reading the docs correctly. That's the way Dell sets them up by default & they advised to leave it that way. I tried burning with Adobe Premeire Elements last night, but no luck. Not surprising, as the other posts seem to imply that it doesn't play well with Nero nor is it the best to burn with anyway.
hmm something not right here? are the drives on the same ide cable? if so end of cable set as master jumper, middle plug set as slave. if both on separate ide cables set plug drives in at end of cable and set both as master... (try this if not already like it, need 2 cables though, thats if you have a spare ide on mobo) (if both on 1 cable, that maybe why only 1 PRIMARY is showing??? just guessing on that.) enable imapi back note: (i have seen drives get working with no jumper in!) even try removing the rom drive, leave burner on its own and test a burn did you check bios for auto detecting?
I forgot to check for the autosensing. The two DVD drives share the same IDE cable, but I think the end of the IDE cable is in the "bottom" drive. I'll swap them and see what happens. In the mean time, I tried to burn a DVD last night and it failed. Here's the log. I don't see the winaspi getting picked up. 1C82-004K-19E5-MAAX-4001-1MA4-**** 1A4K-0800-0000-2529-4295-**** Windows XP 5.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.10.1.2 Internal Version: 7, 10, 1, 2 Recorder: <_NEC DVD_RW ND-3530A> Version: 3.01 - HA 1 TA 0 - 7.10.1.2 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ? CD-ROM: <_NEC DVD_RW ND-3530A >Version: 3.01 - HA 1 TA 0 - 7.10.1.2 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 0 DMA: On DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 1 DMA: Off CdRomPeripheral : _NEC DVD_RW ND-3530A atapi Port 1 ID 0 DMA: On CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 1 DMA: Off === CDRom-Device-Map === _NEC DVD_RW ND-3530A E: CdRom0 HL-DT-ST DVD-ROM GDR8163B F: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 1022MB (1046620kB) Free physical memory: 747MB (765228kB) Memory in use : 26 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 9.5.2008 UDF/ISO compilation 10:08:24 PM #1 Text 0 File SCSIPTICommands.cpp, Line 424 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:08:24 PM #2 Phase 112 File dlgbrnst.cpp, Line 1762 DVD-Video files reallocation started 10:08:25 PM #3 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VIDEO_TS.IFO has been modified 10:08:25 PM #4 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VIDEO_TS.BUP has been modified 10:08:25 PM #5 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VTS_01_0.IFO has been modified 10:08:25 PM #6 Text 0 File DVDVideoCompilation.cpp, Line 616 Content of VTS_01_0.BUP has been modified 10:08:25 PM #7 Phase 113 File dlgbrnst.cpp, Line 1762 DVD-Video files reallocation completed 10:08:25 PM #8 Text 0 File Isodoc.cpp, Line 6666 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 UDF Mode : UDF/ISO bridge UDF Options : automatic UDF Revision : 1.02 UDF Partition Type : physical ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : FALSE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : TRUE 10:08:25 PM #9 Phase 111 File dlgbrnst.cpp, Line 1762 DVD-Video files sorted 10:08:25 PM #10 ISO9660GEN -11 File Geniso.cpp, Line 3343 First writeable address = 0 (0x00000000) 10:08:25 PM #11 ISO9660GEN -11 File Geniso.cpp, Line 3343 First writeable address = 0 (0x00000000) 10:08:25 PM #12 Text 0 File Burncd.cpp, Line 3508 Turn on Disc-At-Once, using DVD media 10:08:25 PM #13 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 2298495 (510:46.45, 4489MB) Last address to be written: 1497951 (332:52.51, 2925MB) 10:08:25 PM #14 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:08:25 PM #15 Text 0 File DlgWaitCD.cpp, Line 2972 Recorder: _NEC DVD_RW ND-3530A, Media type: DVD-R Disc Manufacturer: MCC 02 - RG20 Disc Application Code: 64, Disc Physical Code: 193 10:08:25 PM #16 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 10:08:25 PM #17 Text 0 File ThreadedTransferInterface.cpp, Line 793 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 1497952 (1497952) = #1497952/332:52.52 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1497952 blocks [E: _NEC DVD_RW ND-3530A] -------------------------------------------------------------- 10:08:25 PM #18 Text 0 File ThreadedTransferInterface.cpp, Line 995 Prepare [E: _NEC DVD_RW ND-3530A] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3067805696, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 1497952 | 0 | 0x00 1497952 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:08:25 PM #19 Text 0 File SCSIPTICommands.cpp, Line 215 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:08:25 PM #20 Text 0 File Burncd.cpp, Line 4294 Caching options: cache CDRom or Network-Yes, small files-No (<64KB) 10:08:25 PM #21 Phase 24 File dlgbrnst.cpp, Line 1762 Caching of files started 10:08:25 PM #22 Text 0 File Burncd.cpp, Line 4413 Cache writing successful. 10:08:25 PM #23 Phase 25 File dlgbrnst.cpp, Line 1762 Caching of files completed 10:08:25 PM #24 Phase 36 File dlgbrnst.cpp, Line 1762 Burn process started at 8x (11,080 KB/s) 10:08:25 PM #25 Text 0 File ThreadedTransferInterface.cpp, Line 2721 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 10:08:25 PM #26 Text 0 File DVDR.cpp, Line 3229 Recording mode: Sequential Recording Mode 10:08:25 PM #27 Text 0 File DVDR.cpp, Line 3385 Start write address at LBA 0 DVD high compatibility mode: Yes 10:08:25 PM #28 Text 0 File Cdrdrv.cpp, Line 9872 ---- Disc Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Revision number of maximum recording speed: - Revision number of minimum recording speed: - Revision number table of recording speed: - - - - - - - Class: 0 Start sector number of the current Border-Out: 2FE10 h Start sector number of the next Border-In: 2FFA0 h Media Specific [16..63]: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 10:08:25 PM #29 Text 0 File ThreadedTransfer.cpp, Line 269 Pipe memory size 83836800 10:08:26 PM #30 Text 0 File Cdrdrv.cpp, Line 1352 22:08:26.546 - E: _NEC DVD_RW ND-3530A : Queue again later 10:11:16 PM #31 SPTI -1093 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1093) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x02 Sense Qual: 0x00 CDB Data: 0x2A 00 00 04 13 C0 00 00 20 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 02 Buffer x0bc7aac0: Len x10000 0x00 00 01 BA 44 2E 0E 84 1E 23 01 89 C3 F8 00 00 0x01 E0 07 EC 81 00 00 EF DD D6 1B 98 1D ED 17 63 0xCB 5C 6E 78 20 01 60 BA 08 00 76 00 E4 58 03 FF 10:11:16 PM #32 CDR -1093 File Writer.cpp, Line 303 No seek complete E: _NEC DVD_RW ND-3530A 10:11:23 PM #33 Text 0 File DVDR.cpp, Line 3787 EndDAO: Last written address was 267199 (413BFh) 10:11:29 PM #34 Phase 38 File dlgbrnst.cpp, Line 1762 Burn process failed at 8x (11,080 KB/s) 10:11:30 PM #35 Text 0 File SCSIPTICommands.cpp, Line 261 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:11:33 PM #36 Text 0 File Cdrdrv.cpp, Line 11185 DriveLocker: UnLockVolume completed 10:11:33 PM #37 Text 0 File SCSIPTICommands.cpp, Line 424 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
Heres something on this error ASPI is not necessarily displayed in ALL Nero logs, in most cases it depends on which version of Nero is in use. You are using good quality discs, Verbatim? so I dont think thats a problem.
Checked the IDE cables and everything was OK (end on the top/0/writer). While I had the case open, I re-seated power & IDE on both DVD drives. I guess I don't know where to check for the auto-sensing. Where do I look? Got a can of air & blew out the drive in case I was having a dust issue. Tried to burn another DVD after that this morning and it failed, all (exactly) the same as last night, with the "no seek" error. Yes, I am using Verbatim -R DVDs. Was using some Sony prior to this, but after reading a lot of posts I decided to switch, in case I just had a bad lot of DVDs. This is just getting so frustrating. I'd buy a new drive, but I'm afraid that nothing will change if its a driver/software/system level issue. Is it time to get a new drive?
as above! also look in bios for auto detect drives is enabled... most times its hold delete key on boot up, but should have on screen prompt saying on boot up , read the screen fo more details.
I couldn't find anything regarding autosensing for IDE. However, in the drives section, there were two entries for the IDE. The Master listed the burner and ON. The other one (slave) was OFF. It showed the default as being ON, so I switched it, just to give it a try. Now the Device 1 that has been in PIO Mode is on Ultra DMA Mode 2. Hmm... I tried to burned a DVD and it worked. I'll try a couple more and see how it goes. As with last week, I was able to burn one and then it would start failing again. I haven't been able to burn two in a row for quite a while.
No luck. Tried to burn a data DVD and it failed about 60% of the way through. Data was on the 2nd HD - the one that still appears to have the DMA off. (For the last one, the data came from the other drive.) Here's the log: 1C82-004K-19E5-MAAX-4001-1MA4-**** 1A4K-0800-0000-2529-4295-**** Windows XP 5.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.10.1.2 Internal Version: 7, 10, 1, 2 Recorder: <_NEC DVD_RW ND-3530A> Version: 3.01 - HA 1 TA 0 - 7.10.1.2 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ? CD-ROM: <HL-DT-ST DVD-ROM GDR8163B>Version: 0D20 - HA 1 TA 1 - 7.10.1.2 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 0 DMA: On DiskPeripheral : WDC WD1600JD-75HBB0 iaStor Port 0 ID 1 DMA: Off CdRomPeripheral : _NEC DVD_RW ND-3530A atapi Port 1 ID 0 DMA: On CdRomPeripheral : HL-DT-ST DVD-ROM GDR8163B atapi Port 1 ID 1 DMA: On === CDRom-Device-Map === _NEC DVD_RW ND-3530A E: CdRom0 HL-DT-ST DVD-ROM GDR8163B F: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 1022MB (1046620kB) Free physical memory: 567MB (580904kB) Memory in use : 44 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 14.5.2008 ISO compilation 7:36:24 PM #1 Text 0 File SCSIPTICommands.cpp, Line 424 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 7:36:25 PM #2 Text 0 File Isodoc.cpp, Line 6666 Iso document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : TRUE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : TRUE 7:36:25 PM #3 ISO9660GEN -11 File Geniso.cpp, Line 3343 First writeable address = 0 (0x00000000) 7:36:25 PM #4 Text 0 File Burncd.cpp, Line 3508 Turn on Disc-At-Once, using DVD media 7:36:25 PM #5 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 2298495 (510:46.45, 4489MB) Last address to be written: 949999 (211:06.49, 1855MB) 7:36:25 PM #6 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 7:36:25 PM #7 Text 0 File DlgWaitCD.cpp, Line 2972 Recorder: _NEC DVD_RW ND-3530A, Media type: DVD-R Disc Manufacturer: MCC 02 - RG20 Disc Application Code: 64, Disc Physical Code: 193 7:36:25 PM #8 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 7:36:25 PM #9 Text 0 File ThreadedTransferInterface.cpp, Line 793 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 950000 (950000) = #950000/211:6.50 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 950000 blocks [E: _NEC DVD_RW ND-3530A] -------------------------------------------------------------- 7:36:25 PM #10 Text 0 File ThreadedTransferInterface.cpp, Line 995 Prepare [E: _NEC DVD_RW ND-3530A] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 1945600000, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 950000 | 0 | 0x00 950000 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 7:36:25 PM #11 Text 0 File SCSIPTICommands.cpp, Line 215 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 7:36:25 PM #12 Text 0 File Burncd.cpp, Line 4294 Caching options: cache CDRom or Network-No, small files-No (<64KB) 7:36:25 PM #13 Phase 36 File dlgbrnst.cpp, Line 1762 Burn process started at 12x (16,620 KB/s) 7:36:25 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 2721 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 7:36:25 PM #15 Text 0 File DVDR.cpp, Line 3229 Recording mode: Sequential Recording Mode 7:36:25 PM #16 Text 0 File DVDR.cpp, Line 3385 Start write address at LBA 0 DVD high compatibility mode: Yes 7:36:25 PM #17 Text 0 File Cdrdrv.cpp, Line 9872 ---- Disc Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Revision number of maximum recording speed: - Revision number of minimum recording speed: - Revision number table of recording speed: - - - - - - - Class: 0 Start sector number of the current Border-Out: 2FE10 h Start sector number of the next Border-In: 2FFA0 h Media Specific [16..63]: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................ 7:36:25 PM #18 Text 0 File ThreadedTransfer.cpp, Line 269 Pipe memory size 83836800 7:36:26 PM #19 Text 0 File Cdrdrv.cpp, Line 1352 19:36:26.578 - E: _NEC DVD_RW ND-3530A : Queue again later 7:39:44 PM #20 SPTI -1093 File SCSIPassThrough.cpp, Line 179 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1093) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x02 Sense Qual: 0x00 CDB Data: 0x2A 00 00 08 76 60 00 00 20 00 00 00 Sense Area: 0x70 00 03 00 00 00 00 0A 00 00 00 00 02 Buffer x0c01b380: Len x10000 0x00 00 01 BA 44 34 67 5B 34 99 01 89 C3 F8 00 00 0x01 E0 07 EC 80 00 00 08 20 76 54 17 82 B9 12 31 0x60 76 3E A0 00 00 01 05 22 76 73 11 DB 33 9E 60 7:39:44 PM #21 CDR -1093 File Writer.cpp, Line 303 No seek complete E: _NEC DVD_RW ND-3530A 7:39:45 PM #22 Text 0 File DVDR.cpp, Line 3787 EndDAO: Last written address was 554591 (8765Fh) 7:39:45 PM #23 Phase 38 File dlgbrnst.cpp, Line 1762 Burn process failed at 12x (16,620 KB/s) 7:39:46 PM #24 Text 0 File SCSIPTICommands.cpp, Line 261 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 7:39:50 PM #25 Text 0 File Cdrdrv.cpp, Line 11185 DriveLocker: UnLockVolume completed 7:39:50 PM #26 Text 0 File SCSIPTICommands.cpp, Line 424 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
Tried burning the files a couple more times. Had luck once after I moved the files from the D: drive to the C: drive. Tried that trick again with a 2nd set of files (moving from D to C) and that one failed with the "NO SEEK" error. To me, that means that the DMA setting on the D drive isn't affecting this. Thoughts?
I am at a loss as to where you obtained this particular firmware for this burner, ALL my sources indicate that the correct firmware should be 1.03c.....this is more than likely why your log shows as EDIT: I see you are using a Dell comp, then check out this link for your appropriate firmware...there is 2 for the Dell comp http://drivers.softpedia.com/progSearch You have now increased the speed of your burn, although you are using GOOD quality discs, try slowing burn to 4X
