Need help using team xavier's installer

Discussion in 'Xbox - General discussion' started by Halfflip, Nov 23, 2003.

  1. Halfflip

    Halfflip Member

    Joined:
    Nov 14, 2003
    Messages:
    23
    Likes Received:
    0
    Trophy Points:
    11
    I have burned the ISO to a disc and tried sticking it in my xbox but it tells me that this is not an xbox disc and to eject to proceed. do i need to add a dummy file or do anything special in order to boot this to my xbox. i flashed my bios with the d.6 Blie bios and can see the blue X, but have had no luck installer team xavier's installer. even after reading the read_me and install guide that comes with it. can someone please help. anything advice would be greatly appreciated.
     
    Halfflip, Nov 23, 2003
    #1
  2. Jslayer

    Jslayer Guest

    what did you use to make the iso?
     
    Jslayer, Nov 23, 2003
    #2
  3. Halfflip

    Halfflip Member

    Joined:
    Nov 14, 2003
    Messages:
    23
    Likes Received:
    0
    Trophy Points:
    11
    I used craxtion.
     
    Halfflip, Nov 23, 2003
    #3
  4. Halfflip

    Halfflip Member

    Joined:
    Nov 14, 2003
    Messages:
    23
    Likes Received:
    0
    Trophy Points:
    11
    Ok I extracted the Team Xavier auto-installer ISO and came up with three new files. I now have default.xbe, disk.bin, and evox. But I'm still confused on what to do next. I have burned these files to a TDK CDRW and inserted the disk into my xbox, but the xbox still states that it cannot read the disk. Make sure it a DVD, CD, .... Can someone please tell me exactly what the next step is. Should the xbox be able to read the disk and maybe I'm burning it wrong. I'm using Nero 6 and have successfully flasked my Chameleon with the D.6 Blue BIOS. Or do I now have to FTP into my xbox and download the new extracted files directly to my xbox hard drive? I've been trying to mod my xbox for about a week and have come along very slowly. If anyone can explain to me exactly what the next step is with this Team Xavier auto-installer. It would be greatly appreciated. Yes, I'm a newbie, but we all had to stop somewhere. So please be patient. Thanks again!
     
    Halfflip, Nov 23, 2003
    #4
  5. richard77

    richard77 Member

    Joined:
    Nov 6, 2003
    Messages:
    66
    Likes Received:
    0
    Trophy Points:
    16
    DONT EXTRACT THE ISO!!!!!!!!!!! BURN IT TO A CD USING NERO (select burn from image from one of the menus at the top) AND THEN POP IT IN YOUR XBOX!!!!! It should work then

    Richard
     
    richard77, Nov 23, 2003
    #5
  6. GetModded

    GetModded Guest

    If the disc you tried wouldn't load just try another Brand Name disc.

    RustyDog
     
    GetModded, Nov 24, 2003
    #6
  7. Halfflip

    Halfflip Member

    Joined:
    Nov 14, 2003
    Messages:
    23
    Likes Received:
    0
    Trophy Points:
    11
    Ok, first off I would like to thank everyone for their help! You guys ROCK!!! For everyone else who may be having the same problem I had. You DO NOT extract the team xavier installer. When using nero, you must click on the Recorder tab at the top and choose Burn Image. From there a new window appears and that's where you burn the ISO. Choose no joliet, ISO mode 1, no multisession and you're ready to go. I still can't thank you guys enough for helping me finally mod my xbox!
     
    Halfflip, Nov 24, 2003
    #7

Share This Page