need v551 USB modem driver for 98

Hello, i installed PHT 3.11 and my computer still looks for the driver for v551 and can't find it.
Iam using Windows 98.
Thank you for your help in advance

 

whats PHT 3.11??

never heard that before!!!!

 

i have the same problem upgraded to 3.19 , attemped to configure my phone in win98 and all drivers supplyed with phonetools will not load. same program works fine with xp and the v551

 

u need drivers for Win98Se and am not sure where u can find it, but i remember its somewhere in this motorola forum....

 

well I was told the latest drivers were it 3.21 so I upgraded . the computer sees the v551 but not one driver in the list will allow the computer to operate the phone . apparently the driver for win98se is not in mpt 3.21 ,any ideas anyone??? also the config only sees com 1 and 2 . I've read mpt likes 3,4

 

well soon in this thread am going to post the drivers that suits for Win98Se,WinMe and WinXp, and hope that will help. about the com u can change it to 3 or 4

 

Thanks for your help in advance.
tony

 

no problem at all

 

hey Mossyy, have you had a chance to find that 98se driver yet?

 

ya i have the driver now, so send me ur email via PM and i'l send it over,,,,

 

Hello Mossyy
Can you please send me the Windows 98 driver for v551?

Is there a way to do live update from Mobile Phone Tools 3.11 to 3.23? I only found UPDATE which takes me to the site to purchase the product.

 

Ticocal

to update go to menu>Setup>Live update

about the driver it has been sent

 

Thank you,

 

u r more than welcome

 

Well mossyy , thanks for the files but the program still does not reconize the phone. Begining to think its a com port problem . the program only sees 1& 2.
On my computer with xp the modem for the phone is on com port 4. Need to figure out what port the phone is trying to use in 98se.

 

well then plug ur fone and go to control panel>modem and check on which com is it and i think u can change to 4 or 4 from there.....

 

Well the saga continues, the v551 refuses to operate on com ports 1 & 2 .My computer modem is on 3.I went into system info and watch as I plug in the phone and it looks to load on com port 4 . the software for mpt does not reconize the phone on 4 so does not load the driver . It only sees com 1,2,& 3 .Not 4 . I can't figure out how to make mpt see com port 4 . any ideas anyone?also the device manager will not load the phone on 4 where it wants to live . It also only sees 1&2.I even tried to remove the built in modem and just install the phone to no avail.

 

i guess u have to start from zero, delete everything that belongs to motorola, MPT or P2Kman, and go to the safe mode delete ur drivers from there, and install everything again, start with the drivers, then use the P2Kman to c if u r connected, and if it show that u r connected install MPT 1.23 then update it with 2.21 and check if it works, if its not update it to 3.23, and let me know what will happen,,,,,,

 

Well I finally figured it out . I have not been able to use my v551 with mpt and win98se until just now . I tried to install a new driver (p2k)with no luck . The driver would install but in modem properties There was no com port assigned to the usb modem. I finally went into safe mode and went to device manager . selected the usb hub for the modem and updated the driver there(p2k). I restarted the computer and there it was on com port 4 . I then ran mpt and went to setup . Then changed the modem to the usb modem and wam bam thank you mam. it works . Thanks Mossyy

 

Glad to hear that