OS Question

Discussion in 'Building a new PC' started by Knuck1ez, Jan 27, 2010.

  1. Knuck1ez

    Knuck1ez Regular member

    Joined:
    Nov 22, 2006
    Messages:
    408
    Likes Received:
    0
    Trophy Points:
    26
    Ive been running xp on a 120Gb HDD and decided to install Win7 on a 70gb raptor (same PC) and after installation, theres was no option to get back into xp. Is there anyway to change anything (maybe boot.ini?) to allow me to boot into xp?
    Thanks
     
  2. jony218

    jony218 Guest

  3. Knuck1ez

    Knuck1ez Regular member

    Joined:
    Nov 22, 2006
    Messages:
    408
    Likes Received:
    0
    Trophy Points:
    26
    I installed 7 on a seperate HDD while xp was already installed and xp just dissapeared..
    Thanks for the link though, I might have to reinstall both >8(
     
  4. sammorris

    sammorris Senior member

    Joined:
    Mar 4, 2004
    Messages:
    33,335
    Likes Received:
    7
    Trophy Points:
    118
    If you installed it to a separate hard disk then you should be OK, just remember to select the correct drive in the BIOS. FWIW though, always unplug the HDD you are not installing to when you setup windo0ws.
     
  5. jony218

    jony218 Guest

    You won't have to reinstall either of them. For xp a simple fixmbr/fixboot will get it to boot again.
    With seven, you just need to run a repair from the dvd installation disk.

    To get them both to boot in a dual boot, you need to edit the BCD. When I dual booted xp/vista, they where both on the same drive and it went smoothly.

    You are doing the dual boot correctly, xp first/then seven added second.
     
  6. Xplorer4

    Xplorer4 Active member

    Joined:
    Apr 13, 2006
    Messages:
    1,080
    Likes Received:
    0
    Trophy Points:
    66
    ^irrelevant.

    Its just a matter of switching the boot order of the drives in the bios.
     
  7. Knuck1ez

    Knuck1ez Regular member

    Joined:
    Nov 22, 2006
    Messages:
    408
    Likes Received:
    0
    Trophy Points:
    26
    Thanks guys, Figured it out. But now I have a new problem (Kinda). I have a gigabyte ud3p motherboard and theres 6 SATA ports which are all being used (5 HDD and 1 optical) and I want to add another HDD. While there are 2 purple "gSATA" ports, Im not sure if I should connect anything there. What do those ports do? I thought It would be easier to post this question here instead of a new topic because its kinda relevant.
     
  8. sammorris

    sammorris Senior member

    Joined:
    Mar 4, 2004
    Messages:
    33,335
    Likes Received:
    7
    Trophy Points:
    118
    You can use them fine. They just run off a separate controller since the Intel controller can only work with up to 6 ports. They are coloured purple to highlight that they use the other controller, the only practical downside of this is that they can't be run through the same RAID utility as the other ports.
     
  9. Knuck1ez

    Knuck1ez Regular member

    Joined:
    Nov 22, 2006
    Messages:
    408
    Likes Received:
    0
    Trophy Points:
    26
    Ok thanks alot. And just to be on the safe side, Im gonna put my dvdm drive and 5400Rpm green HDD in those 2 slots because they dont get used as often as my other HDDs.
     
  10. sammorris

    sammorris Senior member

    Joined:
    Mar 4, 2004
    Messages:
    33,335
    Likes Received:
    7
    Trophy Points:
    118
    It probably won't make a difference to performance.
     

Share This Page