im out of hdd room need to burn out some movies. nero (or any other burn prog) quit working months ago. i can figure it out, heres what i do know: --dvd+r rarely burn successfully...when they do it wont playu in my stand alone --dvd rw work about 90% of the time --ive tried all kinds of media, sony to imation to tdk to verbatim --cds burn fine --data dvds burn fine --lead in/lead out used to be quick, now they take forever, and nero usually crashes on lead out 85% of the time --the 1 constant ive noticed is in the nero log under "scsi device map" nothing is listed. every other persons log ive looked at online have something listed there, ...not me! so thats my ??? i guess , why dont i have anything listed under scsi device map btw--2 burners..both stopped burning at the same time. & im using vista ultimate. any response is appreciated
1. what version of nero are you using. 2. try updating your drivers. 3. try other software. about windows vista some software is stall abit upit at the moment. i am running windows vista ultimate so you have media centre try to burn one off with media centre. or try to use the bilt in software. i will do some digging for you on google and see what i can find.
i think the latest nero, but ive tried a few difft ones and as far as the built in crap...no go either, when you 1st put a blank in and it says something like format disc (or whatever) itll say estimating time remaining..and stay that way for ever. btw my drivers are current --updated : so i was looking a few posts down, and it had a link to check dma..so i did. in there it said go to device manager, scroll down to ide ata/atapi controllers, find the primary and 2ndary etc etc.. im not seeing that, all i see listed in mine is ata channel 0 ata channel 0 ata channel 1 ata channel 1 via bus master ide controller-0571 via serial ata controller-3149 this shed any light on nething???
I Spoke to my mate and he said check your burner to see if it set to master or slave and which IDE channel it is on (i.e. IDE 0,IDE 1,) make sure your burner is set to master and is on a seprate IDE channel then your hard drive. If that does not work find out what model/make your burner is and find the right firmware update, flash the burner with updated firmware, BUT make sure it is the right firmware or it could end up killing your burner for good. this thanks to my mate hydromalc and navskin
I don't do vista, and I don't do Nero 7 yet, but you said you've tried several different versions of nero. Did you uninstall and run the clean tools before reinstalling? Have you installed any other burning software? This could mess up nero, especially roxio. Can you post a nero history/error log? This could help us help you.
if you dont do vista how can you help. windows vista is diffrent than any other oprating system. windows vista uninstalls programs in a diffrent way as it remove everthing to do with the name of the program. inc logs and stuff like that.
hobbit112 the only diffrence is that if you are running windows xp its very diffrent to vista. have you thought of upgrading to vista it very good.
try a reinstall of vista it could be a windows problem if that dose not work then i would try to remove one of the drive and then try to burn a dvd that might work or try clean the drive with a lenz cleaner. that is al i can think of now to try.
@jones069 When did both drives go? When you updated to Vista or before? What are the makes and models of them? Right click on the sata (serial ata) controller - I think that's where your DMA will be listed. Nothing showing under scsi devices running Vista is normal - just a Vista thing w/ Nero. Post your Nero log - will be helpfully.
I'm trying to setup nero tv in nero mediahome and it says "cannot set video source" when it try to select my tv tuner card
thats too bad..dont hijack my thread! both drives stopped working at the same time,(stopped burning dvd movies that is- i can burn dvd data/cd fine and dvd rw movies some of the time. i think its got something to do with why i dont show anything under scsi device maps in the nero log. maybe when i put the new power supply in, i changed the order of things. i do remember taking ALL the ide cables off and the drives out to "clean" shit up. somebody mentioned that if i had a burner on the same ide as a hdd????? i dont know, ill take it apart later and see if anythings not connected right. dont really know what im looking 4 tho
So you're saying the drives started working intermittently once you changed the power supply? Anything else change? Make sure each drive is on it's own power connector. Post the Nero log too. I don't think it has anything to do with the drives not showing up under scsi devices - running Vista they don't - running XP they do. Again just a Nero thing. If you looked at the successful cd and data dvd logs you'd see them missing there too.
so..i opened her up disconnected everything and re-set it up in the following order (if i remember correctly) 2ndary ide-->hdd(master) burner2 (slave); primary ide--> burner 1 (set to cs) attached on "master" plug in ide cable. diff't power supply connecters on each burner. i think thats all correct eh? at any rate the burning problem cont EXACTLY unchanged. i saved a log just now, only thing i see wrong is illegal key request but i see that on alot of peoples. low-end verbatims, but ive tried many many kinds of media w/ the same results..and dont comment on the 8x speep cuz ive tried every difft speed w/ no results. heres the log, some1 who knows what theyre doing please have a look and see if anything jumps out at ya h-dog Windows XP 6.0 IA32 WinAspi: - ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM NT-SPTI used Nero Version: 7.5.9.0 Internal Version: 7, 5, 9, 0 Recorder: <DVDRW IDE 16X> Version: A188 - HA 1 TA 1 - 7.5.9.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ? CD-ROM: <DVDRW IDE 16X >Version: A188 - HA 1 TA 1 - 7.5.9.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === === CDRom-Device-Map === DVDRW IDE 16X D: CDRom1 AOPEN DRW4410 E: CDRom3 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981952kB) Free physical memory: 379MB (388584kB) Memory in use : 60 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 5.7.2007 UDF/ISO compilation 5:22:33 PM #1 Text 0 File SCSIPTICommands.cpp, Line 411 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 5:22:34 PM #2 Phase 112 File dlgbrnst.cpp, Line 1746 DVD-Video files reallocation started 5:22:34 PM #3 Phase 114 File dlgbrnst.cpp, Line 1746 DVD-Video files reallocation completed (no file modified) 5:22:34 PM #4 Text 0 File Isodoc.cpp, Line 6509 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 UDF Mode : UDF/ISO bridge UDF Options : automatic UDF Revision : 1.02 UDF Partition Type : physical ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : FALSE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : FALSE 5:22:34 PM #5 Phase 111 File dlgbrnst.cpp, Line 1746 DVD-Video files sorted 5:22:35 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3332 First writeable address = 0 (0x00000000) 5:22:35 PM #7 ISO9660GEN -11 File Geniso.cpp, Line 3332 First writeable address = 0 (0x00000000) 5:22:35 PM #8 Text 0 File Burncd.cpp, Line 3451 Turn on Disc-At-Once, using DVD media 5:22:35 PM #9 Text 0 File DlgWaitCD.cpp, Line 306 Last possible write address on media: 2295103 (510:01.28, 4482MB) Last address to be written: 2286111 (508:01.36, 4465MB) 5:22:35 PM #10 Text 0 File DlgWaitCD.cpp, Line 318 Write in overburning mode: NO (enabled: CD) 5:22:35 PM #11 Text 0 File DlgWaitCD.cpp, Line 2903 Recorder: DVDRW IDE 16X, Media type: DVD+R Disc Manufacturer ID: MCC, Media Type ID: 003, Product revision number: 0 Disc Application Code: 0, Extended Information Indicators: 3 5:22:35 PM #12 Text 0 File DlgWaitCD.cpp, Line 490 >>> Protocol of DlgWaitCD activities: <<< ========================================= 5:22:35 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 821 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [D: DVDRW IDE 16X] -------------------------------------------------------------- 5:22:35 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 1024 Prepare [D: DVDRW IDE 16X] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 2286112 | 0 | 0x00 0 | 1 | 1 | 0x41 | 2286112 | 0 | 0x00 2286112 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 5:22:35 PM #15 Text 0 File SCSIPTICommands.cpp, Line 209 SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME 5:22:35 PM #16 Phase 24 File dlgbrnst.cpp, Line 1746 Caching of files started 5:22:35 PM #17 Text 0 File Burncd.cpp, Line 4278 Cache writing successful. 5:22:35 PM #18 Phase 25 File dlgbrnst.cpp, Line 1746 Caching of files completed 5:22:35 PM #19 Phase 36 File dlgbrnst.cpp, Line 1746 Burn process started at 8x (11,080 KB/s) 5:22:35 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2743 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 5:22:35 PM #21 Text 0 File Cdrdrv.cpp, Line 9234 ---- DVD Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD+R (10), Part Version: 1.0x (1) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 26053F h End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Disc Application Code: 0 / 0 h Extended Information indicators: 3 h Disc Manufacturer ID: MCC..... Media type ID: 003 Product revision number: 0 Number of Physical format information bytes in use in ADIP up to byte 63: 56 Media Specific [16..63]: 00 00 03 4D 43 43 00 00 - 00 00 00 30 30 33 00 38 ...MCC.....003.8 23 54 37 12 02 42 6E 02 - A8 6B 15 15 0B 0B 08 08 #T7..Bn..k...... 01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................ 5:22:35 PM #22 Text 0 File DVDR.cpp, Line 6894 Drive: DVDRW IDE 16X Book Type request [BTC]: DVD-ROM Changing the Book Type was finished successfully, return code 0 5:22:35 PM #23 CDR -1207 File DVDR.cpp, Line 6174 Book Type automatically set to: DVD-ROM 5:22:36 PM #24 SPTI -1066 File SCSIPassThrough.cpp, Line 179 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1066) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x24 Sense Qual: 0x00 CDB Data: 0xAC 00 00 00 00 00 00 00 00 64 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24 Buffer x080d69c0: Len x648 5:22:36 PM #25 Text 0 File DVDPlusRW.cpp, Line 674 Start write address at LBA 0 DVD high compatibility mode: Yes 5:31:35 PM #26 Text 0 File WriterStatus.cpp, Line 113 <D: DVDRW IDE 16X> start writing Lead-Out at LBA 2286112 (22E220h), length 0 blocks 5:33:14 PM #27 SPTI -1135 File SCSIPassThrough.cpp, Line 179 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1135) Sense Key: 0x03 (KEY_MEDIUM_ERROR) Sense Code: 0x0C Sense Qual: 0x00 CDB Data: 0x00 00 00 00 00 00 00 00 00 00 00 00 Sense Area: 0x71 00 03 00 00 00 00 0A 00 00 00 00 0C 5:33:40 PM #28 Text 0 File DVDR.cpp, Line 6894 Drive: DVDRW IDE 16X Book Type request [BTC]: DVD+R Changing the Book Type was finished successfully, return code 0 5:33:40 PM #29 CDR -1135 File ThreadedTransferInterface.cpp, Line 1920 Write error D: DVDRW IDE 16X 5:33:40 PM #30 TRANSFER -24 File ThreadedTransferInterface.cpp, Line 1920 Could not perform end of Disc-at-once 5:33:40 PM #31 Phase 127 File dlgbrnst.cpp, Line 1746 Generating DVD high compatibility borders 5:33:56 PM #32 Phase 129 File dlgbrnst.cpp, Line 1746 Generating DVD borders completed successfully 5:33:56 PM #33 Text 0 File DVDR.cpp, Line 6894 Drive: DVDRW IDE 16X Book Type request [BTC]: DVD+R Changing the Book Type was finished successfully, return code 0 5:33:56 PM #34 Phase 38 File dlgbrnst.cpp, Line 1746 Burn process failed at 8x (11,080 KB/s) 5:33:57 PM #35 Text 0 File SCSIPTICommands.cpp, Line 254 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 5:33:58 PM #36 Text 0 File Cdrdrv.cpp, Line 10467 DriveLocker: UnLockVolume completed 5:33:58 PM #37 Text 0 File SCSIPTICommands.cpp, Line 411 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: File 'Drivers\ADPU160M.SYS': Ver=6.4.645.100 (NT.051018-1332), size=98408 bytes, created 11/2/2006 5:50:35 AM Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon
sorry about the double post, but i wanted to separate the 2 logs. this log is the same vts folder burned on a rw disc. the illegal key request still shows up, but not only does the burn complete successfully..it plays fine (choppy/hanging in a few spots, but ithink thats a result of the scratched and dirty rw disc) the only diff should be the speed cuzz the rw only handles 4x. so now ill try the same vts folder on a dvd+r at 4x. heres that log:: h-dog 0000-004001-0000000 Windows XP 6.0 IA32 WinAspi: - ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 11/2/2004 12:54:32 PM NT-SPTI used Nero Version: 7.5.9.0 Internal Version: 7, 5, 9, 0 Recorder: <DVDRW IDE 16X> Version: A188 - HA 1 TA 1 - 7.5.9.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default (0) -> ATAPI, detected: ? CD-ROM: <DVDRW IDE 16X >Version: A188 - HA 1 TA 1 - 7.5.9.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === === CDRom-Device-Map === DVDRW IDE 16X D: CDRom1 AOPEN DRW4410 E: CDRom3 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981952kB) Free physical memory: 476MB (488012kB) Memory in use : 50 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 5.7.2007 UDF/ISO compilation 5:50:25 PM #1 Text 0 File SCSIPTICommands.cpp, Line 411 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 5:50:26 PM #2 Phase 112 File dlgbrnst.cpp, Line 1746 DVD-Video files reallocation started 5:50:26 PM #3 Phase 114 File dlgbrnst.cpp, Line 1746 DVD-Video files reallocation completed (no file modified) 5:50:26 PM #4 Text 0 File Isodoc.cpp, Line 6509 UDF document burn settings ------------------------------------------ Determine maximum speed : FALSE Simulate : FALSE Write : TRUE Finalize CD : TRUE Multisession : FALSE Burning mode : DAO Mode : 1 UDF Mode : UDF/ISO bridge UDF Options : automatic UDF Revision : 1.02 UDF Partition Type : physical ISO Level : 1 (Max. of 11 = 8 + 3 char) Character set : ISO 9660 Joliet : FALSE Allow pathdepth more than 8 directories : TRUE Allow more than 255 characters in path : TRUE Write ISO9660 ;1 file extensions : FALSE 5:50:26 PM #5 Phase 111 File dlgbrnst.cpp, Line 1746 DVD-Video files sorted 5:50:26 PM #6 ISO9660GEN -11 File Geniso.cpp, Line 3332 First writeable address = 0 (0x00000000) 5:50:27 PM #7 ISO9660GEN -11 File Geniso.cpp, Line 3332 First writeable address = 0 (0x00000000) 5:50:27 PM #8 Text 0 File Burncd.cpp, Line 3451 Turn on Disc-At-Once, using DVD media 5:50:33 PM #9 Text 0 File DlgWaitCD.cpp, Line 306 Last possible write address on media: 2295103 (510:01.28, 4482MB) Last address to be written: 2286111 (508:01.36, 4465MB) 5:50:33 PM #10 Text 0 File DlgWaitCD.cpp, Line 318 Write in overburning mode: NO (enabled: CD) 5:50:33 PM #11 Text 0 File DlgWaitCD.cpp, Line 2903 Recorder: DVDRW IDE 16X, Media type: DVD+RW Disc Manufacturer ID: MBIPG101, Media Type ID: W04, Product revision number: 0 Disc Application Code: 0, Extended Information Indicators: 1 5:50:33 PM #12 Text 0 File DlgWaitCD.cpp, Line 490 >>> Protocol of DlgWaitCD activities: <<< ========================================= Insert empty disc to write to. (Medium in drive: DVD+RW. Medium required by compilation: DVD R/RW, DVD+R DL.) This disc is not empty. (Medium in drive: DVD+RW. Medium required by compilation: DVD R/RW, DVD+R DL.) Accessing disc... (Medium in drive: DVD+RW. Medium required by compilation: DVD R/RW, DVD+R DL.) 5:50:33 PM #13 Text 0 File ThreadedTransferInterface.cpp, Line 821 Setup items (after recorder preparation) 0: TRM_DATA_MODE1 () 2 indices, index0 (150) not provided original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37 relocatable, disc pos for caching/writing not required/ required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [D: DVDRW IDE 16X] -------------------------------------------------------------- 5:50:33 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 1024 Prepare [D: DVDRW IDE 16X] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Session Closed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next Trk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ 0 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 0 | 0x41 | 2286112 | 0 | 0x00 0 | 1 | 1 | 0x41 | 2286112 | 0 | 0x00 2286112 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 5:50:34 PM #15 Text 0 File SCSIPTICommands.cpp, Line 209 SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME 5:50:34 PM #16 Phase 24 File dlgbrnst.cpp, Line 1746 Caching of files started 5:50:34 PM #17 Text 0 File Burncd.cpp, Line 4278 Cache writing successful. 5:50:34 PM #18 Phase 25 File dlgbrnst.cpp, Line 1746 Caching of files completed 5:50:34 PM #19 Phase 36 File dlgbrnst.cpp, Line 1746 Burn process started at 4x (5,540 KB/s) 5:50:34 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2743 Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0 5:50:34 PM #21 Text 0 File Cdrdrv.cpp, Line 9234 ---- DVD Structure: Physical Format Information (00h) ---- Media Type: 0, Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050 Book Type: DVD+RW (9), Part Version: 1.1x (2) Disc Size: 120 mm, Maximum Rate: <not specified> (F h) Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: re-writable Linear Density: 0,267 um/bit, Track Density: 0,74 um/track Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW) End Physical Sector Number of Data Area: 26053F h End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB) Data in Burst Cutting Area (BCA) does not exist Disc Application Code: 0 / 0 h Extended Information indicators: 1 h Disc Manufacturer ID: MBIPG101 Media type ID: W04 Product revision number: 0 Number of Physical format information bytes in use in ADIP up to byte 63: 57 Media Specific [16..63]: 00 00 01 4D 42 49 50 47 - 31 30 31 57 30 34 00 39 ...MBIPG101W04.9 23 00 94 79 64 02 20 00 - 9C 7A 6C 02 20 00 9A 7B #..yd....zl....{ 68 02 20 12 12 10 E0 00 - F0 00 00 00 00 00 00 00 h............... 5:50:34 PM #22 Text 0 File DVDR.cpp, Line 6894 Drive: DVDRW IDE 16X Book Type request [BTC]: DVD-ROM Changing the Book Type was finished successfully, return code 0 5:50:34 PM #23 CDR -1207 File DVDR.cpp, Line 6174 Book Type automatically set to: DVD-ROM 5:50:34 PM #24 SPTI -1066 File SCSIPassThrough.cpp, Line 179 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1066) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x24 Sense Qual: 0x00 CDB Data: 0xAC 00 00 00 00 00 00 00 00 64 00 00 Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24 Buffer x08097180: Len x648 5:50:34 PM #25 Text 0 File DVDPlusRW.cpp, Line 674 Start write address at LBA 0 DVD high compatibility mode: Yes 6:04:42 PM #26 Text 0 File WriterStatus.cpp, Line 113 <D: DVDRW IDE 16X> start writing Lead-Out at LBA 2286112 (22E220h), length 0 blocks 6:04:47 PM #27 Text 0 File DVDPlusRW.cpp, Line 899 Media-Format will be stopped after burning 6:04:47 PM #28 Phase 127 File dlgbrnst.cpp, Line 1746 Generating DVD high compatibility borders 6:04:53 PM #29 SPTI -1066 File SCSIPassThrough.cpp, Line 179 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1066) Sense Key: 0x05 (KEY_ILLEGAL_REQUEST) Sense Code: 0x24 Sense Qual: 0x00 CDB Data: 0xFA 00 00 00 00 00 00 00 00 00 AA FF Sense Area: 0x70 00 05 00 00 00 00 0A 00 00 00 00 24 6:04:53 PM #30 Text 0 File DVDR.cpp, Line 6894 Drive: DVDRW IDE 16X Book Type request [BTC]: DVD+RW Changing the Book Type was finished with error, return code -1066 6:04:53 PM #31 Phase 37 File dlgbrnst.cpp, Line 1746 Burn process completed successfully at 4x (5,540 KB/s) 6:04:54 PM #32 Text 0 File SCSIPTICommands.cpp, Line 254 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 6:04:57 PM #33 Text 0 File Cdrdrv.cpp, Line 10467 DriveLocker: UnLockVolume completed 6:04:57 PM #34 Text 0 File SCSIPTICommands.cpp, Line 411 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: File 'Drivers\ADPU160M.SYS': Ver=6.4.645.100 (NT.051018-1332), size=98408 bytes, created 11/2/2006 5:50:35 AM Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon
Ok when you connected the drives back again ideally the hard disk drive should be on the primary ide and the 2 burners on the secondary ide. If this is a Dell then they prefer the CS jumper setting. Otherwise the jumper should be set to the connection on the ide cable - like master to master. Looking at both drives never are very good and they may be dying out. The Aopen only has a max burn speed of 4x for +R media only. The other burn a BTC/Emprex was last updated in 2005 so newer media like 16x speed may be hit or miss. That could be why your having better luck with RW media - not much has changed with it over the years so most drives support them pretty well. Personally I would replace one of the burners 1st - they are so much cheaper. Heck with all the coasters you've had now that may have paid for one
The other burn a BTC/Emprex was last updated in 2005 so newer media like 16x speed may be hit or miss. where did u see btc/emprex?? ive been trying to find who the manufact. was to get updated firmware
I've seen this drive - Drive: DVDRW IDE 16X show up in quite a few failed burn logs. I have it memorized know I think BTC/Emprex is no longer around. I remember reading something at cdfreaks - but I could be wrong. Here's a link to the info on the drive from the firmware page. edit: fix link
well, no doubt both my drives are getting old and outdated, but its just TOO coincidental that they both quit burning dvd-video at the same time, right after i removed/replaced the guts to change the power supply. thats why i dont think the firmware is to blame either
