Experiencing Difficulty Using DVD RB and CCE? If So, Then Ask Your Questions Here.

What version were you using before/after?

 

Sophocles

Yeah that is what I mean... more or less burn when I get a chance too.

bigorange, jdobbs

Thanks, everything was fine. Just no power for a few days.

 

vurbal, is there a dvd-rb + quenc setup guide?

 

I continued trying out DVD Rebuilder, but no luck so far. This is what I did so far:

(1) Used DVD Decrypter to back up my movie (about 5.7 GB)
(2) Opened up DVD Rebuilder(V 0.56). I chose Transcode(I have One-Click Mode ticked). It continued for hours and hours. At the end of it, there was this error message"Buffer Overflow-Must Abort". When I clicked ok, the transcoding stopped. I still have about 10 GB of free hard drive space.

I looked up the folder.And there were three folders-D2VAVS(3.5 GB), VIDEO_TS(710 MB) and AUDIO_TS.
Any advise would be more than welcome!! I am really very keen to try this out.

Thanks!!!

 

happida69, the 3 folders are correct.

Under options did you go to setup and choose your path to CCE basic and your path for mpeg2dec3dgdll and check add to AVS file?

Also under options-AVS-did you check convert to yuy2O and audio dub? Then under CCE check CCE basic 2.67?

Under mode did you check CCE mode, verbose status window, and dynamically assign cell bitrates?

This is all just a basic checklist of what you must do to ensure RB/CCE is working properly.

Which version of CCE are you using?

Was your error message 0003 or 0004?
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

This is a good checklist from bigorange. If all is in order, I would then recommend trying Smartripper in backup mode to rip the files - and then to RB-CCE without editing.

 

Good morning doc, it must be really early where you're at. Long time, no see, how goes it?

Tried batch with 3 movies, other than a "minor dvd allocation error" on one movie, all went well and all burned. Didn't understand that message tho.
_
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

Yeah, up early here in PAC 10 country. I've been quite busy lately, and only get to drop in every now and then. 'Hope things will settle down soon. I see lots of new interest in RB-CCE, which is nice. Did yo get to try batch mode yet?

 

You must have not seen my edit. Any comment on the allocation error. It actually said burn would probably work, "minor" DVD allocation error, would you like to continue? Strange huh? It only had this message for one movie, the other two were fine.

When I burned tho, all 3 played without problems and looked fine.
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

If your edit was there, I didn't see it. I began my answer just seconds after the email arrived.

I am thinking the allocation error is the result of editing.

 

LOL, normally that would be a good guess because I always edit with remake(unless it's so small it isn't worth the effort), however because this was my 1st time using batch mode i wanted to take it a step at a time, and none were edited, all were entered with a full rip from decrypter.

I thought it strange the message said it was a minor error and would probably work, never seen anything like that before with an error message, have you?

BTW, that was a good straight simple mini-guide for batch mode, good job.
_
_
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

bigorange... ...Thanks for the complement on the Batch mini-guide. Glad it worked.

I've had a couple of [strange] things happen using RB wihtout edited files. I believe both of these DVD's went through Decrypter, and I wasn't able to repeat them the second time through. Your "allocation" error sounds very familiar. I believe I said "yes" and when finished, the final Video_ts folder was missing the initial IFO file ... and Nero wouldn't burn. I Decrypted a second time, and no problem. Over the long term I have had intermittant problems with Decrypter, and find myself using Smartripper the majority of the time now.

This Smartripper use may even change, though, since I recently read where files can be loaded into Remake directly from AnyDVD. I let my trial expire, so I haven't tried it yet. How about you?

 

Yes, I have anydvd and you can go straight into remake if you wish.

I use anydvd quite a bit with other apps, since I don't use RB/CCE except for larger files.
_
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

Bigorange, thanks for your response.Here's the set up info:

"Under options did you go to setup and choose your path to CCE basic and your path for mpeg2dec3dgdll and check add to AVS file?" YES

"Also under options-AVS-did you check convert to yuy2O and audio dub? Then under CCE check CCE basic 2.67? "

AUDIO DUB is not checked. Others are.

"Under mode did you check CCE mode, verbose status window, and dynamically assign cell bitrates?" YES

This is all just a basic checklist of what you must do to ensure RB/CCE is working properly.

"Which version of CCE are you using?" 2.69.01.04

"Was your error message 0003 or 0004?" I believe it was 0004.

Any ideas?? Thanks.

 

Hmm! Did I hear something about a RB/CCE Batch mini guide?

 

Bigorange, I had ripped the movie using DVD Decrypter in File mode. I did not strip anything.

 

Soph, I seem to remember you saying something about a RB/batch guide, Doc isn't stealing your thunder is he? LOL


happida-I had the same problem with 2.69, I switched to CCE 2.67 and it has worked perfectly ever since. I am not the only one to do this. No one seems to know why it makes a difference, some don't believe it does, but I know with 2.69 I got errors 0003 and 0004. How did I guess your error no.? You didn't tell me.

Somewhere in one of these RB/CCE threads there is a URL for CCE 2.67, I would download it, I would keep 2.69 btw, and just put CCE 2.67 in a different folder. You will need your CCE purchase info to load it.

Then run RB/CCE 2.67 and see if your problem is cured. I bet it is!
_X_X_X_X_X_[small] [bold]GO VOLS![/bold]..Dell Media4600, XP,Pentium 4 @2.80GHz/800Mz,512MB,280HDw/8MB,17" flat panel,AIO-A920,8xDVD-ROM,integrated 5.1 audio, HPdc4000,PlextorPX-708UF,LiteOn SO[/small]

 

Bigo

I have both CCE Basic 2.69 and CCE basic 2.67 both installed at the same time and both work fine. I use 2.69 with RB and 2.67 with DVD2DVD-R. All you do is make sure they're installed into a separate folder.

 

Bigorange, thanks for the response. I looked at this thread but I was linked to the webiste http://www.cinemacraft.com/eng/download.html, wherein there is no link to the 2.67 Basic Version. Only 2.69. Is there any other link available?? Would I have to pay for this once again??

Thanks..