Starview frequency range

I know i have posted the question below on a couple of the forums within afterdawn but as yet no response sorry if i am not showing the appropriate etiquitte just desperate for help.

my *view is a clone and i am receiving all the channels, setanta sports is now on bics 411 but i have no sound with it, when i watch a match i have to put a radio on for commentary, her in doors is cracking up any ideas how to resolve the problem?

regards

sadfart

Ps Just tried an automatic scan and there was no change, i have a splitter on the cable would it make a difference if i disconnected the splitter?

any help mucho appreciated

 

try disconnecting the splitter and see, also check your scart cable if there anyway dodgy you will get crap picture or problems with sound

 

Delete the channel and try doing a manual scan at the lowest frequency. Mine is 291.000, obviously dunno where ye are so couldn't confirm this is your lowest frequency but I know the frequency range's are posted somewhere on the site for differing area's.

It should come in at the end of your channel listings on the starview box.

 

hi folks,
tried auto scan without splitter same result evrything tickety boo with allother stations including picture and sound but setanta 1 still appearing on bics 11 good picture but still no sound.

i dont know how to do manual scan the information on bics 11 is 283000khz 64qam 6887ksps not sure what all that means but thought i would include it just in case it helps resolve the problem.

regards sadfart

 

If you want to try a Manual Scan do the following, - From the Affected Channel (Setanta) Press Menu, OK on Installation, Go down to Manual Scan and press OK again, and you will see the frequency you have posted 283.000Mhz appear in Down Frequency, just press OK and it will scan on that one frequency, when finished it will show you what was found. Wait for saving and then exit out to TV, you will most likely find the channels found at the end of your listings, just re-order in Channel Edit and delete the non working one/s. (It may solve your problem, no harm in trying, good luck)

 

malci,

thanks for your speedy response who says there are no more heroes just followed your very simple instructions and hey presto we have sound.

keep the good work up

sadfart

 

Pleased for you, and the wife as well of course, no more mental!! lol, good luck and take care.

 

update for clone starview 1 out now.

 

Yep it sure is, and it was posted directly underneath the OPs request within the hour.

 

Hi All, I hope you can help me! I followed this path with the aim of getting setanta 1 & 2.....
menu>installation>manual scan>down frequency> 238000MHZ > enable network scan.
This worked as I now have the setanta channels with sound on bics 11 and 12!
My problem is that now all my entertainment channels have now got the audio thing on which is used by blind people, as I am not blind this makes viewing very annoying as you can imagine. In addition, bbc 2 now says bbc 2w and has does not show anything at all. I've tried an automatic scan which has not worked, any ideas anyone??

 

Just press the AUDIO button and choose the alternate stream, that will shift the that, as regards the automatic scan, why don't you just make a note of the Frequencies that you could not get like Setanta etc. while you have them, and do a Factory Reset and a Fresh installation and automatic scan whyen finished you can then do a Manual Scan for the channels that you are missing, for example - enter the frequency 238000 in Down Frequency and just press OK, it will then scan on that one frequency (Do Not Enable Network Scan) you must have quite a few double channels at the minute.

 

Thanks for the advice! how do you do a factory reset? am I right in saying that once I have done the factory reset I should re-flash the box and the sort out the missing setanta ones without enabling network scan?

 

No, you do not have to re-flash the box, as I have said, you have been missing The Set**ta channels and now you have got them, you say all be it under bics, if this is correct then just make a note of those Frequencies okay. (Write them down) - Now to do a factory Re-Set, just press Menu and scroll down to Factory Setting and press OK enter pin 0000 and OK to confirm/delete, when you have done this it will ask you to wait, and then it will take you to the Language screen accept English OK and then Installation OK and automatic scan on your provider, when channels found exit out to main menu and enter 1570 and turn the Key Emu to ON. (in other words you are doing a fresh Installation, it does not affect the Firmware you have on your box) - And yes you need to manually scan for the missing Seta*ta ones using the frequencies you have wrote down, using the method I have posted up above twice, (do not enable Network) as you will get a lot of duplicates etc.

EDIT:- To get the Frequencies of channels that you have showing, just press the SL button located above the EXIT button and note the frequencies in Down Frequency, just in case you are not aware of how to find them okay.

 

Hi the link comes up as "NOT VALID"

 

here>>>>>LINK